Backing-grade Beech Veneers 300 x 32 cm

Backing-grade Beech Veneers 300 x 32 cm

Genuine wood sliced-veneer sheets, in sequence.

Dimensions:

Length: 300 cm.

Width: 32 cm.

Thickness: 0.6 mm.

Measurement scaling:

The width is rounded to the covered centimeter. For example, 15.8 cm is given 15 cm.

The length is rounded to 5 centimeters. For example, 257 cm is given 255 cm.

Pictures:

These photos are taken from the veneer sheets you will receive.

While we strive to capture colors as accurately as possible, please note that the colors may vary slightly from the photo. The screen on which the photos are viewed can also affect their appearance.

What are Backing-grade veneers?

The backing grade is a selection of veneer to be used on the non-visible face of a realization.

This grade is technically sound, but aesthetically, it is considered the lowest possible grade.

The backing grade may include pin-knots, knots, figures, flares, minerals, closed splits, discoloration, buckled / wavy, and other aesthetic particularities commonly accepted in a backing grade.

What is Beech Wood?

What are the common Names for Beech Wood?

Beech, Natural Beech, Steamed Beech, European Beech.

What is the botanical name for Beech Wood?

Fagus sylvatica.

Where can we find Beech in nature?

If the oak is the king of our forests, the beech is the prince. It is the second most common species after the oak in our French forests.

Beech is present throughout the Northern Hemisphere, from North America to Japan, but its largest population is found in Europe.

The largest beech forest in Europe is located in Germany, in the Black Forest.

How to Recognize Beech Wood?

Beech is a hardwood characterized by its closed grain. It's very distinctive, small, fine, and short, making the flake easily recognizable, even on a small surface.

Beech has a relatively uniform natural color, typically a creamy white with slight pinkish variations. However, it is usually steamed or boiled, and its color becomes a light pinkish hue. Once a finish is applied, even a clear one, the pinkish tone becomes a light camel color.

What are the mechanical properties of Beech Wood?

Weight: 710 Kg/m3, average at 10-12% humidity.

Janka Hardness: 6460 Newton. For comparison, Oak is 4980 N, and Poplar is 1650 N.

Modulus of Elasticity: 14.31 GigaPascal. For comparison: Ash 12.31 GPa and Poplar 9.75 GPa.

Tensile strength: 110 Megapascals; for comparison, US maple is 109 MPa, and Oak is 47.3 MPa.

What are the uses of Beech Veneers?

Beech veneers are used in furniture, handcrafted decorative items, flooring, stairs, chairs, high-end plywood (including seat shells and bed slats), and decorative veneer panels.

What are wood veneers?

Veneers are thin sheets of wood obtained by slicing or peeling.

Their surface has the appearance of planed wood without any finish or treatment. They are neither glued nor backed with any other material. This means that both sides of the sheets can be used.

Veneers are primarily used to cover less aesthetically pleasing substrates, such as plywood or particleboard, to create furniture or wall panels.

Wood veneers are also used to create decorative objects, including lamps, jewelry, bookmarks, and more.

By assembling several sheets of veneer on top of each other, it is possible to manufacture objects requiring high mechanical resistance, such as skis, bicycle frames, or musical instruments.

The applications of veneer are as varied as they are multiple.

Since veneers are genuine wood, all wood finishing products, whether varnish, stain, or oil, are suitable. The choice of finish will depend on your personal preferences and the object's intended use.

The veneer offered here is a sliced sheet of uniform thickness; however, the thickness may vary from one species to another. The standard thickness is around 0.6 mm.

Although the edges of the veneers have been cut roughly straight, the cut is not perfectly parallel. Some veneers may retain the natural taper of the tree, being slightly wider at the foot than at the top.

Some veneers may have a slight wavy edge (an edge that follows the tree's natural shape) on the sides. In this case, the dimensions indicated correspond to the minimum width of the veneer, as specified in the "Dimensions" paragraph.

How to use veneers?

How to cut the veneers?

Veneers can be easily cut with a utility knife.

For straight cuts, the best results are obtained with a veneer saw.

Use a fretsaw, scalpel, or veneer knife for curved cuts.

Always allow for a slightly larger veneer sheet than your intended surface. This will allow you to adjust the size after gluing for a clean, finished look.

A flush trimmer can also be used to trim the veneer after it has been glued.

When cutting with a utility knife or veneer knife, it is best to cut with the grain of the wood. To check this, run your finger along the edge of the sheet. The direction that feels smoothest is the ideal direction for cutting.

What is veneer splicing?

As the veneers have the width that nature provided, you may need to cover an area wider than the available veneers.

Therefore, you need to splice the veneers by gluing or fixing them side by side with tape to obtain the desired width.

Trim the veneer's edges with a straight and smooth cut to achieve a good joint.

Stick the veneers in place with tape (the blue one is a good choice).

Usually, the veneers are spliced side by side, but to obtain a longer length, they can be done foot by foot.

The splicing must be done before gluing the veneers on the substrate.

What Glue to Use for Veneering?

Several types of gluing are possible.

Vinylic glue (PVA or PVB) is well-suited for porous substrates such as plywood, particleboard, or MDF. The veneers must be pressed with clamps over the entire surface at once.

Note: A technique using vinylic glue and an iron can also be used to glue veneers; however, we strongly recommend using this technique only if other gluing solutions are not feasible.

- Neoprene glue is applied to all surfaces, especially non-porous surfaces, using two coats of glue and marouflage.

- Animal glue, such as hide, sinew, or bone glue, is a product that must be cooked in a double boiler and used hot.

How to Sand Veneers?

Veneers and all our products are made from genuine wood and can be sanded to the desired thickness.

Please do not use a belt sander, regardless of the veneer's thickness, as this could pierce it.

With a 0.6 mm veneer, lightly sand with 120 grit and then finish with 180 or 240 grit. With an orbital sander, 180 grit is already sufficient for most applications.

How to Finish a Veneer Realization?

All finishing products generally used for wood are suitable for finishing our products. For example, you can use a varnish, wax, paint, or oil.

However, ensure that the product you want to use is compatible with the final use of your creation.

More information:

Please look at our tutorials; you might find some valuable tips.

Please contact us by email or phone for any additional information.