Genuine wood sliced-veneer sheets, in sequence.
Length: 85 cm.
Width: 37 cm.
Thickness: 0.6 mm.
Sold by the sheet.
These photos are taken from the veneer sheets you will receive.
Genuine wood sliced-veneer sheets, in sequence.
Length: 85 cm.
Width: 37 cm.
Thickness: 0.6 mm.
The width and the length are rounded to the covered centimeters. For example, 15.8 cm is given as 15 cm.
These photos are taken from the veneer sheets you will receive.
While we strive to capture colors as accurately as possible, please note that the colors may vary slightly from the photo. The screen on which you view the photos can also affect their appearance.
Burl and cluster veneers are rare and reserved for prestigious projects.
Burl veneer comprises grouped pinknots, which are densely packed and usually cover a good portion of the veneer sheet.
Cluster veneer, on the other hand, is characterized by the wild movement of its wood grain. However, clusters can also have pinknots, either isolated or in clusters.
Numerous pinknots mean some pinknots are piercing, and open cracks are considered a natural part of this type of wood.
After gluing, you can fill the small holes with wood putty to complete the finish. Alternatively, you can cut out the larger holes with a cookie cutter before gluing and insert a veneer disc of the same size from a scrap.
By nature, burl or cluster veneer has a lot of end grain, so its sheets are often warped. Even when they have been pressed, they may still be slightly warped.
However, it is necessary to differentiate between the two types of waving:
- Hard waving: It makes a "pop" sound when you press on it with your finger.
In this case, it's advisable to flatten the veneers before using them. There are several methods; please inquire.
- Soft waving, doesn't make any noise. In this case, it isn't a significant problem; press them beforehand to join multiple sheets together.
Sycamore, European maple, Sycamore maple.
Acer pseudoplatanus.
The sycamore maple is one of the most common maples in Europe and is found throughout Europe, down to North Africa, and up to Western Asia.
Sycamore is a hardwood called "white" but with a slightly ivory tone. Unlike its North American cousin, the sugar maple, it does not have "sugar hair." However, Sycamore has small wood-colored pinknots; these pinknots are inevitable, and a sycamore without pinknots is extremely rare.
This forest species is one of the semi-precious hardwoods, but in its figured form (rare, accounting for less than 1% of forest production), it becomes a precious wood.
Sycamore is called "plain" when it is not figured. However, plain Sycamore can occasionally have flames and shadow figures, which are very light figures not marked enough to be considered figured wood.
Weight: 615 to 650 Kg / m3, average weight at 10 - 12% humidity.
Janka hardness: 4680 Newton. For comparison, Oak is 4980 N, and Poplar is 1650 N.
Elasticity: 9.92 GigaPascal, for comparison: Ash 12.31 GPa and Poplar 9.75 GPa.
Flexural Strength: 55 Megapascals (for comparison: US Maple is 109 MPa, and Yew is 96 MPa)
Its natural beauty and strength make it a popular wood for furniture manufacturers, stairs, parquet floors, and paneling.
In instrument making, Luthiers particularly appreciate the veneers of Fiddleback Sycamore for their warm sound, especially for making violins, cellos, and double basses.
In decoration, its light color and fine grain blend perfectly with various interior styles, adding a touch of elegance and modernity.
Veneers are thin sheets of wood obtained by slicing or peeling.
The veneer's surface has the appearance of planed wood without any finish or treatment. It is neither glued nor backed with any other material, which means that both sides of the sheets can be used.
Wood veneers are mainly used to cover less aesthetic substrates, such as plywood or particleboard, and to make furniture or wall panels.
Veneers are also used to create decorative objects such as lamps, jewelry, bookmarks, and more.
By assembling several sheets of veneer on top of each other, it is possible to manufacture objects requiring high mechanical resistance, such as skis, bicycle frames, or musical instruments.
The applications of veneer are as varied as they are multiple.
Since veneers are made of genuine wood, all wood finishing products, such as varnish, stain, or oil, are suitable. The choice of finish will depend on your personal preferences and the object's intended use.
The veneer offered here is a sliced sheet of uniform thickness, but the thickness might differ from one species to another. The standard thickness is around 0.6 mm.
Although the edges of the veneers have been cut roughly straight, they are not perfectly parallel. Some veneers may retain the natural taper of the tree, being slightly wider at the foot than at the top.
Some veneers may have a slight wavy edge on the sides (one that follows the tree's natural shape). In this case, the indicated dimensions correspond to the minimum width of the veneer, as specified in the "Dimensions" section.
Veneers can be easily cut with a utility knife.
For straight cuts, the best results are obtained with a veneer saw.
Use a fretsaw, scalpel, or veneer knife for curved cuts.
Always allow for a slightly larger veneer sheet than your intended surface. This will allow you to adjust the size after gluing for a clean finish.
A flush trimmer can also trim the veneer after it has been glued.
When cutting with a utility knife or veneer knife, it is best to cut with the grain of the wood. To check this, run your finger along the edge of the sheet. The direction that feels smoothest is the ideal direction for cutting.
Since veneers come in the width that nature gave us, you may need to cover an area wider than the available veneers.
Therefore, you must splice the veneers by gluing or fixing them edge to edge with tape to achieve the desired width.
Trim the veneer's edges with a straight, smooth cut to achieve a good joint.
Stick the veneers in place with tape (the blue one is a good choice).
Usually, the veneers are spliced side by side, but to obtain a longer length, they can be spliced foot to foot.
The splicing must be done before gluing the veneers on the substrate.
Several types of gluing are possible.
Vinylic glue (PVA or PVB) is well-suited for porous substrates such as plywood, particleboard, or MDF. The veneers must be pressed with clamps over the entire surface at once.
Note: A technique using vinylic glue and an iron can also be used to glue veneers, but we strongly recommend using this technique only if other gluing solutions are impossible.
- Neoprene glue is applied to all surfaces, especially non-porous surfaces, using two coats of glue and marouflage.
- Animal glue, such as hide, sinew, or bone glue, is a product that must be cooked in a double boiler and used hot.
Veneers and all our products are genuine wood and can be sanded accordingly to the veneer thickness.
Please do not use a belt sander, regardless of the veneer's thickness, as this could pierce it.
With a 0.6 mm veneer, lightly sand with 120 grit and then finish with 180 or 240 grit. With an orbital sander, 180 grit is already sufficient for most applications.
All finishing products generally used for wood are suitable for finishing our products. For example, you can use a varnish, wax, paint, or oil.
However, ensure that the product you want to use is compatible with the final use of your creation.
Please look at our TUTORIALS; you might find some valuable tips.
Please contact us by email or phone for any additional information.
Data sheet
You might also like
Genuine wood sliced-veneer sheets, in sequence.
Length: 85 cm.
Width: 37 cm.
Thickness: 0.6 mm.
Sold by the sheet.
These photos are taken from the veneer sheets you will receive.
English
