Genuine wood sliced-veneer sheets, in sequence.
Length: 275 cm.
Width: 32 cm.
Thickness: 0.68 mm.
Sold by the sheet.
These photos are taken from the veneer sheets you will receive.
Genuine wood sliced-veneer sheets, in sequence.
Length: 275 cm.
Width: 32 cm.
Thickness: 0.68 mm.
The width is rounded to the covered centimeter. For example, 15.8 cm is given 15 cm.
The length is rounded to 5 centimeters. For example, 257 cm is given 255 cm.
These photos are taken from the veneer sheets you will receive.
While we strive to capture the color as accurately as possible, please note that the color may vary slightly from the photo. The screen on which the photos are viewed can also affect their appearance.
Spanish Cedar, Cedro, Bitter Mahogany, West Indian mahogany, Cedro, Cedrat.
Cedrela odorata.
Although commonly called Spanish Cedar, it originates from Central America. Spanish merchants were the first to import it and named it Spanish Cedar to protect their sources.
Spanish Cedar is a species that adapts well to less tropical regions, such as Brittany in France, where it has been planted in public gardens as an ornamental tree. It was also planted in New Caledonia in the 19th century to provide shade for coffee plantations. However, Cedrala odorata has become too invasive over time.
At first glance, Spanish Cedar or Cedro resembles a Swietenia mahogany (Honduras Mahogany) with a slightly charred pore. Still, its pleasantly spicy smell quickly leaves no doubt that it is Spanish Cedar.
Weight: 470 Kg/m3, average at 10-12% humidity.
Janka hardness: 2670 Newton; for comparison, Oak is 4980 N, and Poplar is 1650 N.
Elasticity: 9.12 Gigapascals; for comparison, Ash is 12.31 GPa, and Poplar is 9.75 GPa.
Tensile strength: 70 Megapascals; for comparison, US maple is 109 MPa, and Oak is 47.3 MPa.
It is a wood with good outdoor resistance. However, since the veneer is thin wood, using it for outdoor applications would be risky unless encased in an epoxy shell, such as surfboards.
This wood species has remarkable properties: it is fairly light and resistant. For these reasons, it was widely used in shipbuilding between the late 19th and early 20th centuries.
Today, its best-known use is as an interior veneer for humidors/cigar boxes. Indeed, this wood has several advantages:
It absorbs excess humidity and then releases it if it is too low. This prevents mold on cigars and helps maintain a good humidity level to prevent the tobacco from drying out.
It has a distinctive and elegant peppery scent. This scent repels insects such as the tobacco moth and pleasantly perfumes cigars.
Veneers are thin sheets of wood obtained by slicing or peeling.
Their surface has the appearance of planed wood without any finish or treatment. They are neither glued nor backed with any other material. This means that both faces of the sheets can be used.
Wood Veneers are mainly used to cover less aesthetic substrates such as plywood or particleboard to make furniture or wall panels.
Veneers are also used to create decorative objects such as lamps, jewelry, bookmarks, and more.
By assembling several sheets of veneer on top of each other, it is possible to manufacture objects requiring high mechanical resistance, such as skis, bicycle frames, or musical instruments.
The applications of veneer are as varied as they are multiple.
Since veneers are genuine wood, all wood finishing products, whether varnish, stain, or oil, are suitable. The choice of finish will depend on your personal preferences and the final use of the object.
The veneer offered here is a sliced sheet of uniform thickness, but the thickness might differ from one species to another. The standard thickness is around 0.6 mm.
Although the edges of the veneers have been cut roughly straight, the cut is not perfectly parallel. Some veneers may retain the natural taper of the tree, being slightly wider at the foot than at the top.
Some veneers may have a trace of a waney edge (an edge following the tree's natural shape) on the sides. In this case, the dimensions indicated correspond to the minimum width of the veneer, as specified in the "Dimensions" paragraph.
Veneers can be easily cut with a utility knife.
For straight cuts, the best results are obtained with a veneer saw.
Use a fretsaw, scalpel, or veneer knife for curved cuts.
Always allow for a slightly larger veneer sheet than your intended surface. This will allow you to adjust the size after gluing for a clean finish.
A flush trimmer can also be used to trim the veneer after gluing.
When cutting with a utility knife or veneer knife, it is best to cut with the grain of the wood. To check this, run your finger along the edge of the sheet. The direction that feels smoothest is the ideal direction for cutting.
As the veneers have the width that nature gave us, you might need to cover an area wider than the veneers available.
Therefore, you need to splice the veneers by gluing or fixing them, side by side, with tape to obtain the desired width.
Trim the veneer's edges with a straight and smooth cut to realize good jointing.
Stick the veneers with tape (the blue one is a good choice.)
Usually, the veneers are spliced side by side, but to obtain a longer length, they can be done foot by foot.
The splicing must be done before gluing the veneers on the substrate.
Several types of gluing are possible.
Vinylic glue (PVA or PVB) is well adapted to porous substrates such as plywood, particle board, or MDF. The veneers must be pressed with clamps over the entire surface at once.
Note: A technique using vinylic glue and an iron can also be used to glue veneers, but we strongly recommend choosing this technique only if other gluing solutions are impossible.
- Neoprene glue is applied to all surfaces, especially non-porous surfaces, using two coats of glue and marouflage.
- Animal glue, such as hide, sinew, or bone glue, are pellets that must be cooked in a double boiler and used hot.
Veneers and all our products are genuine wood and can be sanded according to thickness.
Please do not use a belt sander, regardless of the thickness of the veneer, as this could pierce it.
With a 0.6 mm veneer, lightly sand with 120 grit and then finish with 180 or 240 grit. With an orbital sander, 180 grit is already sufficient for most applications.
All finishing products generally used for wood are suitable for finishing our products. For example, you can use a varnish, wax, paint, or oil.
However, ensure that the product you want to use is compatible with the final use of your creation.
Please look at our TUTORIALS; you might find some valuable tips.
Please contact us by email or phone for any additional information.
Data sheet
You might also like
Genuine wood sliced-veneer sheets, in sequence.
Length: 275 cm.
Width: 32 cm.
Thickness: 0.68 mm.
Sold by the sheet.
These photos are taken from the veneer sheets you will receive.
English
