Bloodwood Veneers 270 x 31 cm

Bloodwood Veneers 270 x 31 cm

€32.72
240.629.01 X
20 Items
Available

Bloodwood Veneers 270 x 31 cm

Genuine wood sliced-veneer sheets, in sequence.

Length: 270 cm.

Width: 31 cm.

Thickness: 0.68 mm.

Sold by the sheet.

These photos are taken from the veneer sheets you will receive.

Volume discounts

Quantity Unit discount You Save
3 5% €4.91
5 10% €16.36
10 15% €49.08
Quantity

Bloodwood Veneers 270 x 31 cm

Genuine wood sliced-veneer sheets, in sequence.

Dimensions:

Length: 270 cm.

Width: 31 cm.

Thickness: 0.68 mm.

Measurement scaling:

The width is rounded to the covered centimeter. For example, 15.8 cm is given 15 cm.

The length is rounded to 5 centimeters. For example, 257 cm is given 255 cm.

Pictures:

Pictures herewith are actual photos of the product you will receive.

Species:

Common Names:

Bloodwood,

Red Ebony (False Ebony)

Satine,

Muirapiranga

Note:

Bloodwood is also known as Letterwood. Similar to Letterwood (Amourette, Brosimum aubletti), Bloodwood was used from the 15th century to carve printing characters, particularly large letters and engravings that could not be made from the smaller Boxwood.

Although it also bears the name Red Ebony, it is not a wood from the ebony family but a false ebony.

Botanical Name:

Brosimum rubescens

Origin:

Bloodwood is native to Central and South America, ranging from Panama to Rio de Janeiro, including French Guiana.

Appearance:

Its solid crimson-red color gives it the English name Bloodwood.

It is worth noting that the sapwood of Ribbonwood is cream-colored.

It is a very dense and hard texture wood with a remarkable finish.

Properties:

Density: Approximately 1050 kg/m3 at 10-12% moisture content

Janka Hardness: 12900 Newtons (for comparison: Oak is 4980 N, and Poplar is 1650 N)

Modulus of Elasticity: 20.78 Gigapascals (for comparison: US Maple is 12.62 GPa, and Poplar is 9.75 GPa)

Flexural Strength: 174 Megapascals (for comparison: US Maple is 109 MPa, and Yew is 96 MPa)

Uses:

Ribbonwood has been used in cabinetmaking since the 17th century and has enjoyed great success. In the 18th century, it was favored by cabinetmakers such as Charles Cressent, Antoine Robert Gaudreaus, and Jean-François Leleu.

Today, Ribbonwood is used in both high-end decoration and marquetry, as well as in instrument making.

Its remarkable mechanical properties make it a prime choice for archery, hence one of its many names: Bois d'arc (Bowwood).

Product Description:

Genuine wood-sliced veneer sheets.

These veneers are raw without a finish or any fleece back.

The veneer surface is similar to plane wood. However, it will be preferable to forecast a light sanding after gluing.

The veneers are offered here as wood-sliced sheets of one and unique thickness.

Both faces of these veneers are the same, without fleece back, without glue.

Even if the veneer's sides had been cut relatively straight, it isn't a precise parallel clipping; some veneers may have kept the decreasing shape of the tree, wider at the bottom end and narrower at the top end.

Very occasionally, some veneers' sides have traces of unclipped wane, but our veneers are measured at the narrowest, as explained in the paragraph "sizes."

As genuine natural wood, all finishing products are acceptable as long as they are meant for wood use.

The choice of the finished product must be consistent with the final usage realization.

Use of the veneers:

Cutting:

Veneers can be easily cut with a utility knife.

For straight cuts, the best results are obtained with a veneer saw.

Use a fretsaw, scalpel, or veneer knife for curved cuts.

Always allow for a slightly larger veneer sheet than your intended surface. This will allow you to adjust the size after gluing for a clean finish.

A flush trimmer can also be used to trim the veneer after gluing.

When cutting with a utility knife or veneer knife, it is best to cut with the grain of the wood. To check this, run your finger along the edge of the sheet. The direction that feels smoothest is the ideal direction for cutting.

Gluing:

Several types of gluing are possible.

- With vinylic glue, the veneer is pressed over its entire surface.

- With neoprene glue for all surfaces, especially non-porous surfaces, by applying two coats of glue and marouflage.

With animal glue such as hide, sinew, or bone glue.

With vinyl glue and an iron, apply two thin coats of glue to each piece. This technique should only be used if other gluing techniques are not possible.

Sanding:

Veneers and all our products are wood and can be sanded according to their thickness.

Do not use a belt sander regardless of the thickness of the veneer, as this could pierce it.

With a 0.6 mm veneer, lightly sand with 120 grit and then finish with 180 or 240 grit. With an orbital sander, 180 grit is already sufficient for most applications.

Finishing:

All finishing products generally used for wood are suitable for finishing our products. For example, you can use a varnish, wax, paint, or oil.

However, ensure that the product you want to use is compatible with the final use of your creation.

More information:

Please look at our TUTORIALS; you might find some valuable tips.

Please contact us by email or phone for any additional information.

240.629.01 X
20 Items

Data sheet

Species
Bloodwood
Thickness group
Standard
Grade
Crown-cut

You might also like