Genuine wood veneer sheets.
Selected single veneers, no sequence.
Length: 30 cm (approximately 12 inches).
Width: 22 to 40 cm (approximately 8 to 14 inches), depending on availability.
Thickness: 0.3 mm (approximately 1/80 inches).
Sold by the sheet.
Warning: Please read the complete description carefully.
Genuine wood veneer sheets.
Selected single veneers, no sequence.
Length: 30 cm (approximately 12 inches).
Width: 22 to 40 cm (approximately 8 to 14 inches), depending on availability.
Thickness: 0.3 mm (approximately 1/80 inches).
0.3 mm is twice thinner than the 0.6 mm standard thickness.
This thickness is ideal for making complex wrapping or using its translucency in lampshade craft.
The width is rounded to the covered centimeter, for example, 15.8 cm, giving 15 cm.
To keep the cost of these products as low as possible, unlike other veneers on this website, the pictures of small-size veneers do not represent the actual stock available.
These are veneer sheets with a fixed length of 30 cm (30.5 cm exactly).
These sheets are not in a continuous sequence and may come from different logs.
White Ash is named for its absence of the brown grain pattern that resembles olive wood.
It is the same species as Olive ash/brown Ash. The Bronw/Olive grain pattern typically develops with the tree's age, progressing from the heartwood to the sapwood.
The edges of Olive Ash veneers often retain their youthful, light color.
Generally, White Ash logs are smaller than Oliver Ash logs.
Ash, white ash, Olive Ash, and European white ash.
Fraxinus excelsior.
It is generally native to northern Europe, extending from the tip of Brittany to the Ural Mountains.
Olive Ash is a hard-textured yet lightweight wood with a light white to yellow hue. Its appearance is remarkably uniform, except for the Olive Ash Burl, which showcases contrasting brown grains.
The grain pattern of Ash is usually regular, except for burls.
Ash has an open-pored structure, which is desirable for achieving an accent finish.
Weight: 680 kg/m³, average at 10-12% moisture content.
Janka hardness: 6580 Newton; for comparison, oak is 4980 N, and poplar is 1650 N.
Elasticity: 12.31 Gigapascals; for comparison, American maple is 12.62 GPa, and poplar is 9.75 GPa.
Tensile strength: 51 Megapascals. For comparison, US maple is 109 MPa, and oak is 47.3 MPa.
Olive Ash's remarkable flexibility makes it suitable for a wide range of applications, including tool handles, alpine and Nordic skis, skateboards, surfboards, bows, and other sports equipment, as well as in the construction, automotive, and naval industries.
Aesthetically, Olive Ash is ideal for accent finishes, where its open-pored grain creates striking contrasts. Additionally, it is traditionally used in components subject to friction, such as drawer slides, because its self-lubricating properties reduce wear.
Veneers are thin sheets of wood obtained by slicing or peeling.
Their surface has the same soft touch of planed wood without any finish or treatment. They are neither glued nor backed with any other material. This means that both sides of the sheets can be used.
Veneers are mainly used to cover less aesthetically pleasing substrates, such as plywood or particleboard, to create furniture or wall panels.
Wood veneers are also used to create decorative objects, including lamps, jewelry, bookmarks, and more.
By assembling several sheets of veneer on top of each other, it is possible to manufacture objects requiring high mechanical resistance, such as skis, bicycle frames, or musical instruments.
The applications of veneer are as varied as they are multiple.
Since veneers are genuine wood, all wood finishing products, including varnish, stain, and oil, are suitable. The choice of finish will depend on your personal preferences and the object's intended use.
The veneer offered here is a sliced sheet of uniform thickness; however, the thickness may vary from one species to another. The standard thickness is around 0.6 mm.
Although the edges of the veneers have been cut roughly straight, they are not perfectly parallel to each other. Some veneers may retain the natural taper of the tree, being slightly wider at the foot than at the top.
Some veneers may have a slightly wavy edge on the sides, following the natural shape of the tree. In this case, the indicated dimensions correspond to the minimum veneer width specified in the "Dimensions" paragraph.
Veneers can be easily cut with a utility knife.
For straight cuts, the best results are obtained with a veneer saw.
Use a fretsaw, scalpel, or veneer knife for curved cuts.
Always allow for a slightly larger veneer sheet than your intended surface. This will allow you to adjust the size after gluing for a clean finish.
A flush trimmer can also be used to trim the veneer after it has been glued.
When cutting with a utility knife or a veneer knife, it's best to cut with the grain of the wood. To check this, run your finger along the edge of the sheet. The direction that feels smoothest is the ideal direction for cutting.
Since veneers come in the width that nature gave us, you may need to cover an area wider than the available veneers.
Therefore, you need to splice the veneers by gluing or taping them side by side to achieve the desired width.
Trim the veneer's edges with a straight, smooth cut to achieve a good joint.
Stick the veneers in place with tape (the blue one is a good choice).
Usually, the veneers are spliced side by side, but they can be spliced butt-match to obtain a longer length.
The splicing must be done before gluing the veneers on the substrate.
Several types of gluing are possible.
Vinylic glue (PVA or PVB) is well-suited for porous substrates such as plywood, particleboard, or MDF. The veneers must be pressed with clamps over the entire surface at once.
Note: A technique using vinylic glue and an iron can also be used to glue veneers; however, we strongly recommend using this technique only if other gluing solutions are not feasible.
- Neoprene glue is applied to all surfaces, especially non-porous surfaces, using two coats of glue and marouflage.
- Animal glue, such as hide, sinew, or bone glue, is a product that must be cooked in a double boiler and used hot.
Veneers and all our products are made from genuine wood and can be sanded according to the thickness of the veneer.
Please do not use a belt sander, regardless of the veneer's thickness, as it could pierce the veneer.
With a 0.6 mm veneer, lightly sand with 120-grit sandpaper and then finish with 180- or 240-grit sandpaper. With an orbital sander, 180-grit is already sufficient for most applications.
All finishing products generally used for wood are suitable for finishing our products. For example, you can use a varnish, wax, paint, or oil.
However, ensure that the product you want to use is compatible with the final use of your creation.
Please review our tutorials; you may find some valuable tips.
Please don't hesitate to contact us by email or phone for any further information.
Data sheet
You might also like
Genuine wood veneer sheets.
Selected single veneers, no sequence.
Length: 30 cm (approximately 12 inches).
Width: 22 to 40 cm (approximately 8 to 14 inches), depending on availability.
Thickness: 0.3 mm (approximately 1/80 inches).
Sold by the sheet.
Warning: Please read the complete description carefully.
English
